International VC Tar2 Part Epoxy Primer – Black – 2.5L

International VC Tar2 Part Epoxy Primer – Black – 2.5L

Sale!

Current price is: $78.98. Original price was: $157.95.

Current price is: $78.98. Original price was: $157.95.

Add to cart
Buy Now
SKU: wxz0oacd4ax Category:

Product Description

  • Description

Description

International VC Tar2 is a 2-component epoxy primer that offers superb osmosis protection below the waterline for GRP boats, and anticorrosive protection to steel and alloy surfaces. Providing an excellent barrier to water for osmosis protection and treatment.

Features

  • Self-levelling to give an excellent finish
  • Easy to apply, you can overcoat within hours
  • No sanding required between coats

Specification

  • Brand: International
  • Capacity: 2.5L
  • Area: Below the Waterline
  • Suitable for: Hull
  • Finish/Sheen: Semi Gloss
  • Substrates: Aluminium/Zinc-Galvanised Steel, Epoxy Composite/Carbon Fibre, Cast Iron, GRP/FRP, Lead, Steel
  • Suitable for Aluminium Propellers: Yes
  • Application Method: Airless Spray, Brush, Conventional Spray, Roller
  • Recommended Number of Coats: 3 – 7
  • Practical Coverage: 11.30 m/L
  • Typical Shelf Life: 2 Years

Colour Avaliablity

  • Off-White
  • Black

Preparation

GRPUseSuperCleanertocleanandfullydegreasethesurfacethensandwith240gradewetordrypaper.Rinsewith freshwaterandallowtodry.

OSMOSISPROTECTIONApply 3- 5 coats of VC Tar2.

IMPORTANT: BEFORE APPLYING TO GRP, TEST HULL MOISTURE LEVELS FOLLOWING THE METER MANUFACTURERS

GUIDELINES. FURTHER GUIDANCE ON MOISTURE LEVELS CAN BE OBTAINED FROM AN INDEPENDENT SURVEYOR

OSMOSISTREATMENT Remove existing paint from the gelcoat. Cut open and sand out all blisters and damaged areas. Leave the hull to dry out (normally 6-8 weeks in the autumn). If possible create a high temperature/low moisture condition for drying out. Once dry, fill in all craters with Watertite and sand smooth (substitute fillers, particularly polyester, are not suitable). Apply 7 coats of VC Tar2. Should you be in any doubt, consult a qualified marine surveyor.

STEEL/IRONGritblasttoSa2.Useanglegrinderonsmallareas.Apply4coatsminimumofVCTar2.

ALUMINIUM/ALLOYCleananddegreasewithSuperCleaner.Mechanicallyabradeusingaluminiumcompatiblepaperor lowpressuregritblastusingaluminiumoxide.Apply4coatsminimumofVCTar2.

LEADCleananddegreasewithSuperCleaner.Rubdownwithanemeryclothorpowerwirebrush.Rinsewithfresh waterandallowtodry.Apply3coatsminimumofVCTar2.

Method

Stir individual components well before use. Pour Curing Agent (in can under “hat”) into Base and stir well. Wait a minimum of 15 mins for the air bubbles to disperse. VC General Thinner may be used (up to 5%) to aid application properties and to clean equipment. For optimum flow, apply paint 15 mins to 4 hours after mixing. Apply the following number of coats: GRP (Osmosis Protection) 35 Previously painted (aged, 2component only) 34 (NB not to be used over old antifoulings) Steel/Aluminium/Alloy 4 (min) Lead 3 (min).

Hints

  • Mixing:Stircontentsofeachpartpriortomixing.PourCuringAgent(incanunder”hat”)intoBaseandstirwell.Wait a minimum of 15 mins for the air bubbles to disperse. Mix ratio is 7:1 by volume, as supplied.
  • Thinner VC General Thinner.
  • Thinning Up to 5% thinner may be used to ease application.
  • Cleaner VC General Thinner.
  • Airless Spray Pressure: 210 bar. Tip Size: 15802180.
  • Conventional Spray Pressure: 23 bar. Tip Size: 1.52.0 mm. Thin 2030% using VC General Thinner.
  • Other VC Tar2 takes 5 days to cure fully and the surface may not be scratch resistant until then. Launch the boat according to the recommended launch time of the antifouling applied. Sanding may be required in a dusty environment.

Hazard Warnings

Hazard Pictogram :
Signal Word: Warning
Hazard Statements:

Flammable liquid and vapour
Causes serious eye irritation
Causes skin irritation
May cause an allergic skin reaction
May cause drowsiness or dizziness
May cause damage to organs through prolonged or repeated exposure
Harmful to aquatic life with long lasting effects

Precautionary Statement: General:

Read label before use. Keep out of reach of children. If medical advice is needed, have product container or label at hand.

Prevention:

Wear protective gloves. Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Use only outdoors or in a well-ventilated area. Avoid release to the environment. Do not breathe vapour.

Response:

IF INHALED: Remove person to fresh air and keep comfortable for breathing. IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower. IF ON SKIN: Take off contaminated clothing and wash it before reuse.

Storage:

Keep cool.

Disposal:

Dispose of contents and container in accordance with all local, regional, national and international regulations.

Hazardous Ingredients

Off-White, Black: Phenol, Methylstyrenated, 1-Ethoxypropan-2-ol, Reaction Product: Bisphenol-A-(Epichlorhydrin) and Epoxy Resin, 700

Supplemental Label Elements

Contains epoxy constituents. May produce an allergic reaction.
Wear appropriate respirator when ventilation is inadequate.

Technical Files

Technical Data Sheet

Off-White Part A – Safety Data Sheet

Off-White Part B – Safety Data Sheet

Black Part A – Safety Data Sheet

Black Part B – Safety Data Sheet

View AllClose